It is currently Sat Aug 24, 2019 7:20 am


All times are UTC




Post new topic Reply to topic  [ 2 posts ] 
Author Message
 Post subject: Cisco ASA + Windows 8 (can not ping)
PostPosted: Mon Jul 01, 2013 12:57 am 
Offline

Joined: Mon Jul 01, 2013 12:51 am
Posts: 4
Does anyone able to resolve unable to ping with Qemu host on windows 8? i have both cisco asa and a Qemu host running on my lab and both is not able to ping out to a IOS device, such as the Cisco 3600. anyone can help would be greatly appreciated.




Top
 Profile  
 
 Post subject: Re: Cisco ASA + Windows 8 (can not ping)
PostPosted: Thu Aug 15, 2013 9:23 pm 
Offline

Joined: Thu Aug 15, 2013 9:22 pm
Posts: 1
Interface GigabitEthernet0 "", is up, line protocol is up
Hardware is Linux Ethernet Dev, BW 100 Mbps, DLY 100 usec
(Full-duplex), (100 Mbps)
Input flow control is unsupported, output flow control is unsupported
Available but not configured via nameif
MAC address 0000.ab8f.9900, MTU not set
IP address 192.168.1.1, subnet mask 255.255.255.0
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 pause input, 0 resume input
0 L2 decode drops
0 packets output, 0 bytes, 0 underruns
0 pause output, 0 resume output
0 output errors, 0 collisions, 0 interface resets
0 late collisions, 0 deferred
0 input reset drops, 0 output reset drops
input queue (blocks free curr/low): hardware (0/0)
output queue (blocks free curr/low): hardware (0/0)
ciscoasa# sh interface ip br
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0 unassigned YES manual up up ????
GigabitEthernet1 unassigned YES unset administratively down up
GigabitEthernet2 unassigned YES unset administratively down up
GigabitEthernet3 unassigned YES unset administratively down up
GigabitEthernet4 unassigned YES unset administratively down up
GigabitEthernet5 unassigned YES unset administratively down up
ciscoasa#


no ping to router, another asa.. to anywhere ((

R1#
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#interf fa0/0
R1(config-if)#ip address 192.168.1.2 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#exit
R1(config)#exit
R1#pi
*Mar 1 00:01:33.203: %SYS-5-CONFIG_I: Configured from console by console
R1#ping 192.168.1.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
R1#ping 192.168.1.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms

windows 7 x64 gns3 v0.8.4




Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 2 posts ] 

All times are UTC


Who is online

Users browsing this forum: No registered users and 0 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group

phpBB SEO