Thanks for your reply, Jeremy.

I am uing windows XP w/ SP3.

May I know when this new version will be released ?

Today or Tomorrow :) (GMT +10).

_________________
Jeremy
GNS3 Staff

Just tested it. ASA is now working fine on new 3.07 release. Thanks Jeremy!!!

However, I have problem to save the config, I tried the "wr mem" and the work around "copy running-config flash:/.private/startup-config"
But, I lost all configs once the ASA is reloaded. Any help would be greatly appreciated. Thanks.

ciscoasa# wr mem
Building configuration...
Cryptochecksum: 6e33e06b 255d8b92 90c27d70 9f5b4de4

%Error copying system:/running-config (Not enough space on device)
Error executing command
[FAILED]
ciscoasa#
ciscoasa#
ciscoasa# copy running-config flash:/.private/startup-config

Source filename [running-config]?

Destination filename [/.private/startup-config]?
Cryptochecksum: 6e33e06b 255d8b92 90c27d70 9f5b4de4

%Error copying system:/running-config (Not enough space on device)
ciscoasa#

Try:

copy run disk0:/.private/startup-config

WHere are these files ?

"irst i uncompress the qemu-0[1].10.2-windows to the gns3 directory and then uncompress the Qemu-0.11.0-windows-Lite to cover the qemu-0[1].10.2-windows "

I cant find them anywhere, I tried the patched qemu I used before and even thats not working....

Any idea why the OP's tab don't match up to the current version? I.e. the qemu-ing TAB, for example? Or why there aren't any screenshots of it actually working?

If anyone has a SS of it working, out of the box- I'd love to see it.

Or even if there was a hack or two thrown into it to make it work, that would be good too.


I'm not Chinese, so if I am missing something- speak up.

I've gone through these instructions and can get ASA to start ok but do have the following problem.

i2c_read_byte_w_wait() error, slot = 0x4, device = 0xb0, address = 0 byte count = 1. Reason: I2C_SMBUS_UNSUPPORT

Total SSMs found: 0
Ignoring PCI card in slot:0 (vendor:0x0 deviceid:0x0)
Ignoring PCI card in slot:1 (vendor:0x0 deviceid:0x0)
Ignoring PCI card in slot:2 (vendor:0x0 deviceid:0x0)
Ignoring PCI card in slot:3 (vendor:0x0 deviceid:0x0)
Ignoring PCI card in slot:4 (vendor:0x0 deviceid:0x0)
Ignoring PCI card in slot:5 (vendor:0x0 deviceid:0x0)
Ignoring PCI card in slot:6 (vendor:0x0 deviceid:0x0)

Total NICs found: 6
Error in ioctl SIOGIFINDEX
Failed to open linaeth for interface 0 - verify the support in kernel

Error in ioctl SIOGIFINDEX
Failed to open linaeth for interface 1 - verify the support in kernel

Error in ioctl SIOGIFINDEX
Failed to open linaeth for interface 2 - verify the support in kernel

Error in ioctl SIOGIFINDEX
Failed to open linaeth for interface 3 - verify the support in kernel

Error in ioctl SIOGIFINDEX
Failed to open linaeth for interface 4 - verify the support in kernel

Error in ioctl SIOGIFINDEX
Failed to open linaeth for interface 5 - verify the support in kernel

INFO: Unable to read firewall mode from flash
Writing default firewall mode (single) to flash
WARNING: Unable to write firewall mode to flash, this is normal if flash is
not formatted.
--------------------------------------------------------------------------
. .
| |
||| |||
.|| ||. .|| ||.
.:||| | |||:..:||| | |||:.
C i s c o S y s t e m s
--------------------------------------------------------------------------

Cisco Adaptive Security Appliance Software Version 8.0(2)
Cannot open interface card (media_ethernet/port/id/0)
pix_idb_create: Unable to get link capabilities 0
pix_idb_create: Unable to get nic_stats for port 0
Cannot open interface card (media_ethernet/port/id/1)
pix_idb_create: Unable to get link capabilities 1
pix_idb_create: Unable to get nic_stats for port 1
Cannot open interface card (media_ethernet/port/id/2)
pix_idb_create: Unable to get link capabilities 2
pix_idb_create: Unable to get nic_stats for port 2
Cannot open interface card (media_ethernet/port/id/3)
pix_idb_create: Unable to get link capabilities 3
pix_idb_create: Unable to get nic_stats for port 3
Cannot open interface card (media_ethernet/port/id/4)
pix_idb_create: Unable to get link capabilities 4
pix_idb_create: Unable to get nic_stats for port 4
Cannot open interface card (media_ethernet/port/id/5)
pix_idb_create: Unable to get link capabilities 5
pix_idb_create: Unable to get nic_stats for port 5



So I am not able to configure any of the Ethernet Interfaces.


Anyone else out there had this issue..???


Thanks.

Having the exact same issue...

Create five loopbacks.

Change ASA interface type to pcnet

now start ASA

It will work..

vijayjuan, have tried setting up multiple loopback interfaces and this makes no difference.
This error has nothing at all to do with loopback interfaces.

Thanks.