It is currently Mon Dec 11, 2017 2:07 am


All times are UTC




Post new topic Reply to topic  [ 9 posts ] 
Author Message
 Post subject: issues connecting to real network on win8
PostPosted: Fri Nov 15, 2013 12:46 am 
Offline

Joined: Fri Nov 15, 2013 12:30 am
Posts: 7
I have been having a lot of trouble getting GNS3 to talk to a real network lately.
I have been doing relatively simple setups. I am not sure what has changed.

(3725) R4 - fa1/15 802.1q ====== PC NIC (CLOUD) ====== fa0/3 802.1q SW3 (3550EMI)


int vlan 120 10.0.12.4/24-------------TRUNK---------------int vlan 120 10.0.12.3/24

I have tried using my realtek onboard NIC's and my Intel PCI-X 1000Pro Dual port server adapter.

I am getting strange things with CDP. Here is on the REAL 3550:

Code:
SW3#sh cdp n
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone

Device ID        Local Intrfce     Holdtme    Capability  Platform  Port ID
R4               Fas 0/1           124          R S I     3725      Fas 1/15


And then here is the virtual 3725:

Code:
R4#sh cdp n
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater

Device ID        Local Intrfce     Holdtme    Capability  Platform  Port ID
R4#


Can't ping across.

I am on Windows 8. I set this SAME thing up on my Mint laptop and it works flawlessly. Is there anything with Windows 8 that could be causing the problem or what am I missing?

Regards,

xtropx




Last edited by xtropx on Fri Nov 15, 2013 3:11 am, edited 1 time in total.

Top
 Profile  
 
 Post subject: Re: unexplainable issues connecting to real switch
PostPosted: Fri Nov 15, 2013 3:11 am 
Offline

Joined: Fri Nov 15, 2013 12:30 am
Posts: 7
What I have tried:
    Reloading the router in GNS3 after configuring it.
    Checking the config on each of the routers. (Ensuring they are /24 and in 10.0.12.x, ensuring they are dot1q trunks, enabled, and speed 100/duplex full)
    Moving between the pci-x nics and the realtek nics on my main board.
    Disabling unused nics.
    Running GNS3 as administrator
    Running GNS3 in compatibility mode for Windows 7
    Checking to see if priority and vlan are enabled in configuration of nic settings. They are.
    Re-installing winpcap
    http://www.intel.com/support/network/sb/CS-005897.htm
    Disabling ZoneAlarm firewall, and windows firewall
    Uninstalling ZoneAlarm firewall completely, and turning off windows firewall
    Using older versions of GNS3


Top
 Profile  
 
 Post subject: Re: issues connecting to real network on win8
PostPosted: Fri Nov 15, 2013 12:00 pm 
Offline

Joined: Thu Jul 26, 2012 11:19 pm
Posts: 143
Location: U.K.
There are issues with Windows stripping the vlan tags.
- What is your NIC MTU set to?
- If you run Wireshark on the physical interface can you see the VLAN tags arriving from the 3550?

_________________
GNS3 0.8.4 running on Windows 8.1
GNS3 0.8.4 running on CentOS 6.5


Top
 Profile  
 
 Post subject: Re: issues connecting to real network on win8
PostPosted: Fri Nov 15, 2013 2:23 pm 
Offline

Joined: Fri Nov 15, 2013 12:30 am
Posts: 7
Hello nickbeee thanks for the reply. After spending most of the day on it yesterday I decided to use wubi and copy my IOS images over.

Works PERFECT in ubuntu, same network interfaces. So I can confirm this is a windows issue.
I believe I did set the MTU for at least 1 of the network interfaces in windows a bit higher before, but I can't quite remember.


Top
 Profile  
 
 Post subject: Re: issues connecting to real network on win8
PostPosted: Fri Nov 15, 2013 2:48 pm 
Offline

Joined: Thu Jul 26, 2012 11:19 pm
Posts: 143
Location: U.K.
I think I have it working here now, W8.1 with a real 3550. Set MTU for > 1500 mine has option for Jumbo and I set 2k.
Attachment:
jumbo.jpg
jumbo.jpg [ 49.19 KiB | Viewed 9852 times ]


Then I found it was necessary to run GNS3 with administrator privs. I also have WinPcap installed in W7 compatibility mode.

EtherSwitch 3725 -
Code:
R1-SW#sh cdp nei
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater

Device ID        Local Intrfce     Holdtme    Capability  Platform  Port ID
S3550.NoWindows  Fas 1/0            156         R S I     WS-C3550- Fas 0/24



And then 3550 -
Code:
S3550#sh cdp nei
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
                  D - Remote, C - CVTA, M - Two-port Mac Relay

Device ID        Local Intrfce     Holdtme    Capability  Platform  Port ID
R1-SW            Fas 0/24          126              S I   3725      Fas 1/0


I'll try some vlans across the trunk later when I have more time to see if the VLAN tag stripping issue is there... HTH.

_________________
GNS3 0.8.4 running on Windows 8.1
GNS3 0.8.4 running on CentOS 6.5


Top
 Profile  
 
 Post subject: Re: issues connecting to real network on win8
PostPosted: Fri Nov 15, 2013 4:28 pm 
Offline

Joined: Thu Jul 26, 2012 11:19 pm
Posts: 143
Location: U.K.
Examining the interface with Wireshark, I tried to ping a SVI I created in the vlan on the 3550. I can see 802.1Q tagged packets going out with ARP boradcasts, but the ARP replies from the switch have the 802.1Q tags stripped.

I then dicovered there is a Realtek utility for creating/managing VLANS on Windows so I downloaded and installed this - It's the Windows Diagnostic Program here. After installing it I see some extra drivers appear on the NIC and there is a nice configuration tool to add extra tagged vlans which appear as additional network interfaces. I can ping with a tagged vlan using one of these but I still can't get it to work with GNS3 using the native vlan interface.

I've followed suggestions to disable vlan tagging and priority on the native interface but no success yet. I'll have another go at re-installing WinPcap in case anything has changed.

Now if you want to break out a handful of virtual machines from your PC to a switch over a .1Q trunk then this utility is perfect... Unless you have time to burn I'd go with Linux ;-)

Attachment:
realtek_diags.jpg
realtek_diags.jpg [ 50.4 KiB | Viewed 9850 times ]

Attachment:
realtek_diags2.jpg
realtek_diags2.jpg [ 50.19 KiB | Viewed 9850 times ]

_________________
GNS3 0.8.4 running on Windows 8.1
GNS3 0.8.4 running on CentOS 6.5


Top
 Profile  
 
 Post subject: Re: issues connecting to real network on win8
PostPosted: Fri Nov 15, 2013 8:59 pm 
Offline

Joined: Fri Nov 15, 2013 12:30 am
Posts: 7
nickbeee

Thanks for taking the time to lab this out. I really appreciate it.
I have also increased the MTU and installed winpcap again using win7 compatibility settings.
I haven't had much luck either. I have also found the drivers for my Intel NIC's are from 2009, and there are no Win 8 drivers available (just WIN7_PROx64)
One could consider us having some success, however, as we have indeed identified the problem to be Windows 8.

This is rather unfortunate as my plan was to build a MPLS L3VPN cloud in GNS3 to use as the WAN connection for my voice lab (VLAN from each "PE" to my 2811's), and still be able to bind NIC's to CIPC (save $$$ on IP Phones) Always something right? =\

I might try just going back to windows 7 and seeing if that corrects the problem, or just run GNS3 on my mint laptop for now.

Again, thanks for the help. :)


Top
 Profile  
 
 Post subject: Re: issues connecting to real network on win8
PostPosted: Sat Dec 14, 2013 7:52 am 
Offline

Joined: Sat Nov 23, 2013 9:57 am
Posts: 1
I am on Windows 8. I set this SAME thing up on my Mint laptop and it works flawlessly. Is there anything with Windows 8 that could be causing the problem or what am I missing?

_________________
GuL


Top
 Profile  
 
 Post subject: Re: issues connecting to real network on win8
PostPosted: Tue Aug 19, 2014 7:47 pm 
Offline

Joined: Tue Aug 19, 2014 7:40 pm
Posts: 2
I finally got my Realtek PCIe GBE Controller to do router on a stick with Windows 8.1 / Server 2012 R2!

Here's how:

1. I updated my drivers to the latest: http://www.realtek.com.tw/downloads/dow ... Down=false

2. Once installed, went to my regedit in: HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Control\Class\{4D36E972-E325-11CE-BFC1-08002BE10318}\00nn
Where nn is the physical instance of the network port where you want to capture the VLAN tags.

3. Added / Edited the following DWORDS:

MonitorModeEnabled - 1
MonitorMode - 1
*PriorityVLANTag - 0
SkDisableVlanStrip - 1

4. Restarted my machine, and voila! Working router on a switch! No need to use Linux!




Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 

All times are UTC


Who is online

Users browsing this forum: No registered users and 0 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group

phpBB SEO