|About the native vlan
|Page 1 of 1|
|Author:||dellpe [ Sat Feb 08, 2014 8:25 am ]|
|Post subject:||About the native vlan|
I am attempting to move the "Native" (Cisco Term), Untagged (Huawei Term) from VLAN 1 to VLAN 700.
I have a Trunk "TRK1" on the Huawei S5700-24TP-SI-AC aggregating 8 Gig Interfaces together connectng to an EtherChannel on the Cisco 6506 which is also aggregating 8 Gig Interfaces together. Everything was working fine when I first stood everything up using VLAN 1 as the Untagged / NATIVE Vlan. (Yes, I know, why did you change it - another story).
I thought it would be very easy to change the NATIVE / Untagged VLAN but I am running into issues.
On the Cisco switch, I am receiving no events; but the Huawei , I am constantly receiving events.
Here is what I have configured on the Cisco Side....
switcHuaweiort trunk encapsulation dot1q
switcHuaweiort trunk allowed vlan 1,5,300,500
switcHuaweiort mode trunk
CO22DCWCRK1SW1#sho int port-channel 5 trunk
Port Mode Encapsulation Status Native vlan
Po5 on 802.1q trunking 1
Port Vlans allowed on trunk
Port Vlans allowed and active in management domain
Port Vlans in spanning tree forwarding state and not pruned
Per this output, I am using VLAN 1; however, the Huawei thinks differently.
Here are the events I am recieving on the Huawei Switch...
I 05/21/13 18:19:40 00828 lldp: PVID mismatch on port F20(VID 1)with peer device port Gi4/8(VID 700)(363)
I 05/21/13 18:19:44 00828 lldp: PVID mismatch on port F18(VID 1)with peer device port Gi4/7(VID 700)(363)
I 05/21/13 18:19:44 00828 lldp: PVID mismatch on port F16(VID 1)with peer device port Gi4/6(VID 700)(363)
I 05/21/13 18:19:44 00828 lldp: PVID mismatch on port F10(VID 1)with peer device port Gi4/3(VID 700)(363)
I 05/21/13 18:19:45 00828 lldp: PVID mismatch on port F12(VID 1)with peer device port Gi4/4(VID 700)(363)
I 05/21/13 18:19:52 00828 lldp: PVID mismatch on port F6(VID 1)with peer device port Gi4/1(VID 700)(362)
I 05/21/13 18:19:57 00828 lldp: PVID mismatch on port F14(VID 1)with peer device port Gi4/5(VID 700)(362)
I 05/21/13 18:19:58 00828 lldp: PVID mismatch on port F8(VID 1)with peer device port Gi4/2(VID 700)(362)
Here is configuration snippets from the Huawei 5412zl
trunk F6,F8,F10,F12,F14,F16,F18,F20 trk1 trunk
VLAN ID : 1
Name : DEFAULT_VLAN
Status : Port-based
Voice : No
Jumbo : No
Port Information Mode Unknown VLAN Status
---------------- -------- ------------ ----------
Trk1 Untagged Learn Up
I tried calling Huawei Technical Support and was told I must use VLAN 1 as the Untagged VLAN. I don't believe this is true because I am using VLAN 700 between an Huawei 2910 and the same Huawei 6506 and have no issues. The only difference is there are no aggregating ports.
I am thinking I either need to reboot the Huawei Switch or make the changes on the Huawei end (Far Side) moving to VLAN 700 as the Untagged VLAN, shutting down the port channel on the Cisco Side, make the change on the Cisco side and bring up the port channel.
Does anyone have other suggestions?
Thanks in advance...
|Author:||GNS33046 [ Sat Feb 15, 2014 2:13 pm ]|
|Post subject:||Re: About the native vlan|
So you want different native vlans on two sides of the etherchannel? If not, just set the cisco side to 700 as the native vlan, I think, it'll solve the problem.
Another solution - just turn the LLDP off on the either side (it generates these messages).
|Page 1 of 1||All times are UTC|
|Powered by phpBB® Forum Software © phpBB Group